Clarke CWL1000CF Manuál s instrukcemi

GC071040”(1000mm) WOOD LATHEWITH COPY FUNCTIONModel No CWL1000CFPart No 6501670OPERATING & MAINTENANCEINSTRUCTIONSOPERATING & MAINTENANCEINSTR

10ASSEMBLY OF THE STAND1. Assemble the front & rear legs,supports and top plates using thecoachbolts, nuts and washers asshown in Fig 1.2. Assembl

114. Fit the leadscrew hub (79) ontothe leadscrew axle (78) andsecure with a grub-screw (50).If not already fitted, screw theleadscrew handles (113) i

12ASSEMBLING THE COPY TOOL 1. Install the copy toolholder rack(64) into the hole in the copyfollower body (53) and drive itthrough using the handwheel

13OPERATION1. Ensure the cutting tool, tool rests and tailstock are securely locked inposition before starting work.2. Always rotate the workpiece by

14COPY TURNING1. Take the template object whichis to be copied and markdiagonal lines on each end inorder to show the centre pointbefore installing it

15MAINTENANCEIt is essential that the machine is properly maintained. Always inspect beforeuse. Any damage should be repaired and faults rectified. Th

16MELBORP SESUAC SNOITSEGGUSnurtonlliwrotoM..hctiwsnekorb/evitcefeD.1.elbacrewopdegamaD.2esool,tiucricnepO.3denrubrosnoitcennoc.rotomtuorekaerbtiucric

17TECHNICAL SPECIFICATIONPlease note that the details and specifications contained herein, are correct at thetime of going to print. However, CLARKE I

18oN noitpircseD oN noitpircseD1leehWdnaH23reveLtfihSdeepS201x6MwercSburG33gnirpSlioC3mrAtroppuS438MtuN4retemaidmm8rehsaW53mm52x8MtloB5enihcaM8x6Mwerc

19PARTS DIAGRAMWhen requesting spare parts, please quote the reference DDCWL1000followed by the number (1-118) on the following parts lists.

2INTRODUCTIONThank you for purchasing this CLARKE Wood Lathe.Before attempting to operate the machine, it is essential that you read thismanual thorou

20PARTS LISToN noitpircseD oN noitpircseD36mm52x6MtloB4953x61MtloB46kcaRredlohlooTypoC59aid61rehsaW56noiniPredlohlooTypoC69deBehtaL66aidmm8pilcriC79ai

21PARTS DIAGRAMWhen requesting spare parts, please quote the reference DDCWL1000followed by the number (1-118) on the accompanying parts lists.

22PARTS DIAGRAMACCESSORIESThe following range of accessories is also available from your Clarke dealer:8-Piece Chisel Set Part No: 65006494-Jaw Indepe

23DECLARATION OF CONFORMITY

3CONTENTSIntroduction ... 2Guarantee ...

4GENERAL SAFETY RULESImportant Note: Although the operation manual contains extensive instructionon safe working with power tools, every power tool in

5before connecting to power source and/or battery pack, picking up orcarrying the tool.4.Remove any adjusting key or wrench before turning the power t

6WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BEHAZARDOUS TO YOUR HEALTH. ALWAYS OPERATE THE LATHE IN A WELLVENTILATED AREA. USE A DUST COLLECTI

7ELECTRICAL CONNECTIONSWARNING! Read these electrical safety instructions thoroughlybefore connecting the product to the mains supply.Before switchi

8MAIN COMPONENTSA B C E D F G H I J KJ Tail-stock BodyK Tail-stock Advancing HandleL Tool Rest SupportM FaceplateN Open WrenchO T-Spanne

9UNPACKING & ASSEMBLYWhen unpacking, check for damage or omissions etc. Any found should bereported to your CLARKE dealer where the lathe was orig